Dalek Gun z Doctora Who

51 (polubienia)
5231 (odsłony)
Ten produkt jest dostępny tylko jeśli posiadasz konto w serwisie My Mini Factory
×
Kolor:

To jest moja wersja pistoletu Daleków. Staram się przygotować wszystkie części na Comic-Con w tym roku. I could of went with standard rods "Arrow Rods" but then I would of paid between $2 and $5 per rod and I need 8. This way I can print each rod for about $.05 cents. W dłuższej perspektywie byłoby to tańsze, Zapłać za pręty strzał i gazu, w ten sposób zaoszczędziłem pieniądze. Aktualizacja to przezroczyste rury, Będą świecić światłami L.E.D. Kiedy dostanę to zrobić, zamieszczę kilka zdjęć. ale do tego czasu ciesz się. 8/20/2017: Zaktualizowany wygląd wewnętrznego Gun Tube ze światłami L.E.D. dla 7 różnych ustawień pistoletu kolorowego. Nowe elementy to uchwyt L.E.D. Holder jest pusty, więc możesz włożyć rurkę, aby dodać maszynę do dymu lub użyć E-Cig, aby wydmuchać dym z pistoletu. Po wklejeniu spacji należy wlać czystą żywicę epoksydową do rury pistoletu, aby upewnić się, że L.E.D. są bezpieczne w rurze. Plus jasne Epoxy pozwoli L.E.D. do rozprzestrzeniania ich światło choć na rurce dla głównego efektu świetlnego. Po wyschnięciu będzie 3 przyciski na światło, aby umożliwić 7 różnych zmian kolorów dla różnych poziomów symulowanego ognia pistoletu.

O autorze:
tlmxcpmpp
I just started printing april of 2017. Been a Cosplay peron for alot longer. I got into 3D Printing because i've spent weeks if not months building Comic-Con and Cosplay props. Since i got into 3D Printing i've made, designed and printed all my Comic-Con parts. I use to buy my 3D Printers from eBay. In fact my first 4 were from eBay. 1st TronXY x1 with a print bed of 150x150x150 2nd Tronxy P802a with a print bed of 220x220x300 3rd Kossel Delta with a print bed of 180x300 4th TronXY X3a with a print bed of 220x220x350 Home Made 5th Mega TronXY X1 with a print bed of 440x440x300 6th EX Delta with a print bed of 220x452 7th Mega EX Delta with a print bed of 405x305 8th Corexy 350x350x400 9th Corexy 400x400x400 My latest design the Mega EX Delta, prints faster and quiter then any of myother printers. When i made the Mega TronXY X1 i wanted a larger print bed so i could print my Comic-Con/Cosplay props. Turns out it printed very good, however it tock forever to print large items. so that is when i made the Mega EX Delta. I did a time test with the Mega TronXY X1 and my EX Delta, Same parts same infill same specs on both machines. and the Delta Printed item in 8 hours, The Mega TronXY X1 tock 18 hours. That is when i redesigned my Mega TronXY X1 into the Mega EX Delta printer.

Opinie

Ten model nie ma recenzji. Chcesz być pierwszym recenzentem? Najpierw musisz wydrukować model.